Search found 8 matches
- Wed Jun 20, 2007 9:21 pm
- Forum: (LEGACY) 331-354-392 HEMIs
- Topic: Spark Plug Recommendation
- Replies: 1
- Views: 3583
Spark Plug Recommendation
Need a little help here. Getting ready to fire up my 354H and was wondering what spark plug to use. I currently have Autolite 85's set at .035 but would like confirmation. My engine is normally aspirated with a 650 AVS, MSD electronic ignition, 10.5:1 CR and 270 adv dur cam. I will be running pump g...
- Sun Apr 15, 2007 5:51 pm
- Forum: (LEGACY) 331-354-392 HEMIs
- Topic: Cam specs for stock 56 new Yorker 354
- Replies: 1
- Views: 3738
- Sun Apr 15, 2007 8:19 am
- Forum: (LEGACY) 331-354-392 HEMIs
- Topic: Late 727 T/F to early Hemi Adapter?
- Replies: 3
- Views: 5735
Late 727 T/F to early Hemi Adapter?
I am hoping to gain some advice and insight with the various suppliers of early hemi to late model T/F adapter plates. I have completed my 354 and I am in the process of rebuilding and beefing up a late ('74) T/F. I will be installing this engine/trans combo in a 56 Chrysler. I have researched and f...
- Tue Feb 27, 2007 6:16 pm
- Forum: (LEGACY) 331-354-392 HEMIs
- Topic: Carb and KD Linkage braket w/ Hot Heads Intake
- Replies: 0
- Views: 3013
Carb and KD Linkage braket w/ Hot Heads Intake
What carb and KD linkage bracket system would work with the HotHeads intake on a 354? Is there something off the shelf available or does it need to be fabricated? My engine will be going back into a 56 NYer so I will be using the same accel. pedal. I do not have any of the orginal linkage for the ca...
- Tue Feb 27, 2007 5:02 pm
- Forum: (LEGACY) 331-354-392 HEMIs
- Topic: Need some help with Valve Covers
- Replies: 10
- Views: 10484
- Sun Feb 25, 2007 6:30 pm
- Forum: (LEGACY) 331-354-392 HEMIs
- Topic: Need some help with Valve Covers
- Replies: 10
- Views: 10484
Both the deck and heads have been milled. All of the holes have been bottom tapped. The ARP stud lengths may be the primary issue. The studs are located in the proper position realtive to length. I used studs in lieu of bolts for reliability. Torquing a stud is a single axis function of stress. Bolt...
- Sat Feb 24, 2007 8:55 pm
- Forum: (LEGACY) 331-354-392 HEMIs
- Topic: Need some help with Valve Covers
- Replies: 10
- Views: 10484
Need some help with Valve Covers
I have recently completed the modifications to my engine and I am in the process of dressing it out. I used ARP studs for the heads and valve train without realizing that the valve covers hit the top of the studs. I would like to reuse my original valve covers to defer the cost of new ones and have ...
- Mon Feb 12, 2007 5:24 pm
- Forum: (LEGACY) 331-354-392 HEMIs
- Topic: Aftermarket Pulley and Bracket Supplier
- Replies: 1
- Views: 3458
Aftermarket Pulley and Bracket Supplier
Other than HotHeads and PAW are there any suppliers of aftermarket pulleys and brackets for the early hemi (Chrysler 354)? Are there any pulleys and brackets from another engine that will work on the early hemis (Chrysler 354)? I contacted march and they were of no assistance and interest. Regards, ...