Search found 20 matches
- Tue Oct 30, 2007 5:37 pm
- Forum: (LEGACY) Early Dodge / DeSoto HEMIs
- Topic: 241 Dodge Red Ram Hemi...HELP...
- Replies: 3
- Views: 10042
I guess there are two ways. If the engine can be idled slow, You can adjust while running. Back off untill it clicks and tighten up some. There is a spec for the clearance at the valve with the lifter collapsed. I think it is .06 to .21. You would have to pull the pushrods and drain the lifters.This...
- Mon Sep 03, 2007 10:30 pm
- Forum: (LEGACY) Early Dodge / DeSoto HEMIs
- Topic: 241 Dodge Red Ram Hemi...HELP...
- Replies: 3
- Views: 10042
- Wed Aug 15, 2007 4:28 pm
- Forum: (LEGACY) Early Dodge / DeSoto HEMIs
- Topic: HELP !! 241 Spark Plug Tubes
- Replies: 1
- Views: 4254
- Fri Jun 29, 2007 9:35 pm
- Forum: (LEGACY) Early Dodge / DeSoto HEMIs
- Topic: Valve Cover Studs/Bolts..241 Hemi
- Replies: 3
- Views: 8071
- Sat Feb 10, 2007 1:54 pm
- Forum: (LEGACY) Early Dodge / DeSoto HEMIs
- Topic: Water Pump rebuild kits
- Replies: 3
- Views: 5228
- Thu Feb 08, 2007 4:54 pm
- Forum: (LEGACY) Early Dodge / DeSoto HEMIs
- Topic: Oil fill tube 241
- Replies: 2
- Views: 4150
- Thu Feb 08, 2007 4:53 pm
- Forum: (LEGACY) Early Dodge / DeSoto HEMIs
- Topic: Water Pump rebuild kits
- Replies: 3
- Views: 5228
Water Pump rebuild kits
Anybody know where to buy some 241-270 Dodge water pump rebuild kits?
I don't want to run the chevy pump and the original pumps are getting old. Would like a fresh kit. Thanks.
I don't want to run the chevy pump and the original pumps are getting old. Would like a fresh kit. Thanks.
- Sun Dec 31, 2006 1:59 pm
- Forum: (LEGACY) 331-354-392 HEMIs
- Topic: 318/340 harmonic balancer
- Replies: 3
- Views: 5139
- Sat Dec 30, 2006 4:05 pm
- Forum: (LEGACY) Early Dodge / DeSoto HEMIs
- Topic: 315 HEMI-Can anyone give me a value? pics attached
- Replies: 10
- Views: 12025
- Tue Nov 14, 2006 1:36 pm
- Forum: (LEGACY) Early Dodge / DeSoto HEMIs
- Topic: 54-55 Dodge Exhaust Valve Seats?
- Replies: 2
- Views: 4007
- Wed Oct 11, 2006 1:04 pm
- Forum: (LEGACY) Early Dodge / DeSoto HEMIs
- Topic: will it fit?-also need heads
- Replies: 7
- Views: 6394
- Fri Feb 10, 2006 10:21 pm
- Forum: (LEGACY) Early Dodge / DeSoto HEMIs
- Topic: new to early hemi's-please help
- Replies: 3
- Views: 5764
Really nothing interchanges. The lifters and valve keepers and some front covers is about all. The 241 will make good power but not 500HP. It's main problem is shrouding around the titake valve bosses. The 325's finially got a flat passage around the boss and the power went way up. I would look for ...
- Fri Feb 10, 2006 10:11 pm
- Forum: (LEGACY) Early Dodge / DeSoto HEMIs
- Topic: Desoto flywheel
- Replies: 1
- Views: 3278
In depends on what kind of bellhousing/adapter you will use. If you buy the HotHeads setup with the special flywheel, you will use a late model Chrysler starter with it. You can use any Chrysler,Dodge or Desoto flywheel(yes even the 6's)with your starter but must find an old adapter or like I did an...
- Sat Jun 25, 2005 8:02 pm
- Forum: (LEGACY) Early Dodge / DeSoto HEMIs
- Topic: 1956 dodge royal lancer 315
- Replies: 1
- Views: 3519
- Tue Jun 14, 2005 12:03 pm
- Forum: (LEGACY) Early Dodge / DeSoto HEMIs
- Topic: 270 hemi heads on 315 poly block
- Replies: 11
- Views: 9229
The block is fine the way it is . No modification to the block is needed or possible. The problem is entirely in the heads. If you look at the heads,you see that there is just a slightly oversise hole for the pushrods to go thru. The holes would need to be enlongated so the pushrods could lineup wit...
- Thu Jun 09, 2005 8:52 am
- Forum: (LEGACY) Early Dodge / DeSoto HEMIs
- Topic: 270 hemi heads on 315 poly block
- Replies: 11
- Views: 9229
Hello all, The rocker geometry is the same. The problem is that the push rods do not come straight up but are angled. The cam is well above the crank but the pushrods end right over the center of the cylinders. When the deck was raised the angle of the pushrods was changed.Chrysler widened the deck ...
- Mon Jun 06, 2005 6:17 pm
- Forum: (LEGACY) Early Dodge / DeSoto HEMIs
- Topic: 270 hemi heads on 315 poly block
- Replies: 11
- Views: 9229
- Sat Nov 16, 2002 8:33 am
- Forum: (LEGACY) Early Dodge / DeSoto HEMIs
- Topic: After Market Intakes
- Replies: 46
- Views: 46946
Dodge intake manifold
I had a thought that a good manifold for the 241/270 could also be used on the 315/325 by using spacer plates like are used when 354 heads are used on 392's. It is not done now because the are no good manifolds for the small engines!
- Tue Oct 29, 2002 6:48 pm
- Forum: (LEGACY) Early Dodge / DeSoto HEMIs
- Topic: 241 Dodge Motor Mounts
- Replies: 1
- Views: 4791
241 dodge mount
I built a Hurst style mount for my 241 by tapping out the two lower front cover holes on both sides to 3/8 I've run this for 12 years with no problems. I don't see why it would not work with a chevy pump.
- Sun Oct 27, 2002 9:10 pm
- Forum: (LEGACY) Early Dodge / DeSoto HEMIs
- Topic: After Market Intakes
- Replies: 46
- Views: 46946
Dodge/ DeSoto intake
Would like single four for the low deck Dodge. A modern 180 high-rise would wake up these engines! Would also love to be able to buy the old Crager/Offy 0401 trans addapter for all the short bell-housing engines to the early Ford thans. I use one with a flathead to chevy adapter to get early Ford cl...